1

Tip of the Month – July 2019

Losses at the silage storage.

It has been discussed many times but the ration what is calculated should be lying at the feeding fence.

Calculations and plans for the feeding rations come from analyses, and a plan, usually made with your feeding advisor.

For some reason it occasionally still goes wrong. The silage might have gotten warm which results in loss of energy and taste. Inevitably, the cows will eat less and receive less energy that what was calculated.

What also happens is that crows, starlings and ducks, spend a lot of time at your roughage storage. Predominantly for the corn kernels. Besides taking away valuable energy and starch, and walking around in the storage, they also shit in the cows food

This also happens in the stable…

By keeping the silage storage as clean as possible, and by pulling a protective cover every day over open silage we can eradicate these forms of energy/taste loss.

Making the stable “bird-proof” won’t be easy.

Also pay attention to what extent the sun can shine on the open surface of the silage, this also dries and heats more than intended.




Tip of the Month – June 2019

Make note of the details

Most engineers are proud of the DeLaval VMS and how it works. They would be eager to tell what they know and what you can do to improve your workflow. What they don’t always know is what you don’t know. For example, a farmer could think that milk cups do not connect properly by a few, or more, cows is normal, or sounds that you now find normal but that are not. If the farmer doesn’t make note of the details, then the technician would have to coincidentally experience the issue in order to solve it.

So, make sure to always have your phone or a pen and notebook with you. Make a list of things for the technician to take a look at and they’ll let you know if anything is out of the ordinary. Having the possibility to take notes would also make your work easier. If you think of something while you’re standing behind your barn or in the middle of the field, you could just jot it down and make note of it.




Tip of the Month – Mai 2019

Making more effective use of activity measurement.

You know that the best time to inseminate cows is usually between 60 – 90 days after the calving date.
That is the time that the cow has likely been immersed in negative energy for a while. This means she gives already a few month more milk than the amount of energy that she can absorb from the feed she receives.
This also means that the cow does not always clearly show that she is in heat. Sometimes, this means that the cow does not always achieve 1+ 2 ++ and 3 +++.
And this doesn’t get any better during hot summer days either …

Most cows only show their heat for 4 – 7 hours and often also at night. During this time, you are not all the time in the stable, but the activity meter is.
Thus, it is very important that the system displays correct measurements. For this it is important to know that the transponders are good – (there’s a checklist in DelPro for that) – that they’re not too loose or tight around the neck – (place a flat hand between neck and collar ) – and that the antenna is not too close to the cow recognition place, such as the VMS, selection gate, or too close to electric motors, thick walls, solar panels, cables, etc.

Since DelPro version 5.2, a “Worklist Activity” is available in which the latest knowledge of possibilities is applied using smart filters.
Through these filters, you can also find those cows that have too little activity for a +.

In this list, cows in heat are categorized as: too early for insemination, correct insemination moment or a return. It then churns out a proposal for the right insemination moment!
Lastly, the category “too little activity” you find the cow who is not fit.
This information worklist results in advice about what you can do with the cow.

Users rate this list very positively, which proves that it adds value to the system!

Ask your technician or DeLaval DelPro Advisor for this “Worklist Activity” list!




Tip of the Month – April 2019

Flies transfer bacteria: How do you keep the place clean?

Most causative agents of udder inflammation can be divided into cow-bound bacteria and environment-related bacteria.

Bacteria related to the environment, such as the common Uberis Streptococci, is often spread through beds that are unclean.
Or uncleaned areas, such as those near or under water troughs, cow brushes, fences, etc. This dirt is taken back into the cubicles. The cow will lie down in it and spread it further.
Or Milk equipment / cluster  is not clean enough between milkings so could also play a role.

Cow-bound bacteria such as Staphylococci Aureus and Streptococci Agalaction spread from cow to cow or from milk to cow. So milk leakers, wet cubicles, and uncleaned milk utensils should be cleaned properly on the outside and the inside, since spreading could begin there.

But these cow-bound bacteria can also be passed on by flies!

And they are always in every puddle of milk….

Tackle fly control consequently in time. This is also very important for udder health.

 

And are you already grazing or are you planning to graze?

Read more tips on this topic below:

https://www.harrytuinier.nl/en/2018/08/01/tip-van-de-maand-augustus-2018/

https://www.harrytuinier.nl/en/2017/05/01/tip-van-de-maand-mei-2017/




Tip of the Month – March 2019

Do you have a good replacement?

Do you have a manual for when you’re suddenly unavailable? Is there someone who knows enough about your farm and your cows? Is there someone to replace your job around the VMS, the calves or feeding practices?

In the meantime, trainees at agricultural schools and agri-business farm care services in the Netherlands are learning about the possibilities to replace a farmer with an automatic milking system. It’s even possible to complete exams in these courses!

In general, it is smart to be a proponent of these initiatives. More important, it could prove incredibly useful for when you yourselves are suddenly unavailable.